@article { author = {Mohebbiyan, Mohammad and Hasannezhad, Ali akbar and Shafaeii moghadam, Hadi and Taghipour, Nader}, title = {Petrogenesis, ore geology, geochemistry and geothermometry of the Jouzbon copper index, south-east Damghan}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {1-18}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.1}, abstract = {The Jouzbon Cu index (~1.5 wide and 100 meters’ length), at the south-southeastern parts of Damghan city belongs to the Torud–Chah Shirin volcanic belt. This belt contains calc-alkaline volcanic rocks. The Cu mineralization has occurred between two major faults, the Torud Fault at south and the Anjilu Fault at north. The volcanic and intrusive rocks in this belt include quartz-diorites, quartz-monzonites, dacites and andesites. These rocks show porphyritic, granular and poikilitic textures. The prevailing alteration phases of this region are characterized by sericitization, silicification, calcification, and propylitic alteration. The main mineralization phases of the Jouzbon region are dominanted by occurrence of the sulfides and oxide minerals including pyrite, chalcopyrite, galena, bornite and hematite. Secondary minerals such as covellite , chalcocite , malachite and iron hydroxide are also common. Geochemical observations show that the host rocks are related to a alumina-saturated calc-alkaline magma with volcanic arc (VAG) signature. Fluid inclusion studies on quartz testified a narrow homogenization temperature but a wide salinity, ranging from 130 to 190 ° C and 4 to 14.5 wt%  NaCl equivqlent respectively. Geothermometry assay, based on morphology of pyrite crystals, yielded a temperature in the range of ~250°C for the alteration zone. The compiled data testified that mineralization probably has occurred at the depth of ~ 100 meters below the surface during the epithermal conditions, similar to the IOCG-type deposits.}, keywords = {Jouzbon,Geochemistry,Fluid inclusion,Epithermal,Morphology of pyrit}, title_fa = {بررسی سنگ شناسی، کانه زایی، زمین شیمی و زمین دماسنجی در نشانه مس جُوزبن، جنوب شرق دامغان}, abstract_fa = {نشانه رگه­ای مس جُوزبن با ابعادی به پهنای 5/1 متر و طول حدوداً 100 متر در 120 کیلومتری جنوب – جنوب شرق دامغان و در بخشی از کمربند آتشفشانی ترود – چاه شیرین واقع شده است. این کمربند دارای سنگ­های آتشفشانی کالک آلکالن می باشد. کانه­زایی های این کمربند تحت تاثیر دو گسل اصلی، گسل ترود در جنوب منطقه و گسل انجیلو در شمال منطقه، قرار دارد. سنگ­های آتشفشانی و نفوذی منطقه مورد مطالعه از نوع کوارتز دیوریت، کوارتز مونزونیت، داسیت، آندزیت می­باشند. بافت غالب سنگ­های این منطقه نیز، پورفیری، گرانولار و پویکیلیتیک می­باشد. دگرسانی های مشاهده شده شامل سریسیتی شدن، سیلیسی شدن، کلسیتی شدن و پروپیلیتیک می­باشد. کانه­زایی منطقه در قالب کانی­های سولفیدی از جمله پیریت، کالکوپیریت، گالن و بورنیت و نیز کانی اکسیدی هماتیت رخ داده است. کانی­های ثانویه از قبیل کولیت، کالکوسیت، مالاکیت و هیدروکسید­های آهن قابل مشاهده است. براساس مطالعات زمین شیمیایی، می­توان گفت که سنگ میزبان منطقه از یک ماگمای کالک آلکالن اشباع از آلومین منشاء گرفته و در ارتباط با یک کمان آتشفشانی می­باشد. با توجه به مطالعات سیالات درگیر انجام شده بر روی کانی کوارتز، مشخص گردید که دامنه دمای همگن شدگی بین 130 تا 190 درجه سانتی­گراد و شوری محلول در محدوده ۴ تا ۵/۱۴ درصد وزنی معادل NaCl تغییر می­کند. همچنین دماسنجی انجام شده بر مبنای ریخت­شناسی بلورهای کانی پیریت، دمای حدود C°250 را برای زون دگرسانی، روشن می­سازد. این داده­ها حاکی از آن است که کانی سازی احتمالا در عمقی حدود 100 متر زیر سطح و در شرایط سطح گرمایی و از نوع کانسارهای آهن – مس- طلا صورت گرفته است.}, keywords_fa = {جوزبن,دامغان,زمین شیمی,سطح دمایی,سیالات درگیر}, url = {https://esrj.sbu.ac.ir/article_96809.html}, eprint = {https://esrj.sbu.ac.ir/article_96809_f6fd3d644d1496ad5ac9dc2b878950c9.pdf} } @article { author = {Ahmadi, Reza}, title = {Ore reserve evaluation of sodium sulfate deposit in the central part of Mighan-Arak ‎using geometric and geostatistical methods}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {19-33}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.19}, abstract = {In present research geometric method using Surfer software and geostatistical estimation ‎method have been used to evaluate sodium sulfate reserve in the central part of Mighan-‎Arak sedimentary basin. Using geometric method, average assay of the deposit and net ore ‎reserve were calculated 25.1 percent and 3223581.7 tons respectively. In order to employ ‎geostatistical method, first assay and thickness data of test pits, was statistically analyzed. ‎The results of this stage showed a log-normal distribution for assay data and a normal ‎distribution for thickness data. According to the results of variography and analysis of ‎spatial structure, ordinary block log kriging was employed for assay data as well as inverse ‎squared distance method for thickness data. By this method the size of estimated blocks ‎was selected 60*58 m, average assay of sodium sulfate was obtained 24.98 percent with ‎average standard deviation of 1.09 percent, average thickness of blocks was gained about ‎‎2.57m with average standard deviation of 0.23 m while the upper and lower limit of the ‎mineral deposit are 5275221.4 and 6286683.8 tons respectively in the reliability surface ‎of 95 percent. Based on the results of this research, the difference of calculated reserve by ‎geometric method through Surfer software and kriging is 2557370.9 tons that means 44.2 ‎percent. However the results of kriging estimation are highly accurate and more reliable ‎due to be unbiased having minimum estimation error. ‎}, keywords = {}, title_fa = {ارزیابی ذخیره بخش مرکزی کانسار سولفات سدیم میقان اراک با استفاده از روش‌های هندسی و زمین‌آماری}, abstract_fa = {در پژوهش حاضر از روش­های تخمین هندسی با استفاده از نرم­افزار سرفر و زمین آماری کریجینگ، به منظور ارزیابی ذخیره بخش مرکزی کانسار سولفات سدیم حوضه رسوبی میقان اراک استفاده شده است. با استفاده از روش هندسی متوسط عیار کانسار، 1/25 درصد و متوسط ذخیره خالص ماده معدنی 7/3223581 تن محاسبه شد. برای استفاده از روش زمین­آماری، ابتدا داده­های عیارسنجی و ضخامت ماده معدنی چاهک­های اکتشافی، مورد پردازش­های آماری اولیه قرار گرفت. نتایج حاصل از این مرحله، توزیع لاگ نرمال را برای داده­های عیارسنجی و توزیع نرمال را برای داده­های ضخامت ماده معدنی نشان داد. براساس نتایج عملیات واریوگرافی و تجزیه و تحلیل ساختار فضایی، روش تخمین لاگ کریجینگ معمولی بلوکی برای داده­های عیارسنجی مورد استفاده قرار گرفت و برای تخمین ضخامت نیز از روش عکس مجذور فاصله استفاده شد. با این روش ابعاد بلوک­های تخمینی 58×60 متر، متوسط عیار سولفات سدیم کانسار، 98/24 درصد با میانگین انحراف استاندارد 09/1 درصد، ضخامت متوسط بلوک­ها در حدود 57/2 متر با انحراف معیار 23/0 متر و حدود بالا و پایین ذخیره خالص ماده معدنی تخمینی در سطح اعتماد 95% به ترتیب برابر با 4/5275221 و 8/6286683 تن به دست آمد. براساس نتایج پژوهش صورت گرفته اختلاف میزان ذخیره محاسبه ‌شده به روش هندسی با استفاده از نرم­افزار سرفر و روش کریجینگ برابر با 9/2557370 تن یعنی در حدود 2/44 درصد می‌باشد که نتایج روش تخمین کریجینگ به علت نااریب بودن و حداقل بودن خطای تخمین، دقیق­تر بوده و از درجه اعتبار بیشتری برخوردار است. }, keywords_fa = {تخمین ذخیره,حوضه رسوبی میقان اراک,روش زمین آماری,روش هندسی,سولفات سدیم}, url = {https://esrj.sbu.ac.ir/article_96858.html}, eprint = {https://esrj.sbu.ac.ir/article_96858_d31260e29cae5b4984fcc4140bf7a45c.pdf} } @article { author = {Nemati, Majid}, title = {Seismic investigation of 2010 Bardsir and 2011 Sirch and Kahnooj moderate earthquakes in Kerman province}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {33-48}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.33}, abstract = {During one year, the Bardsir earthquake (2010/07/31, MS=5.8), the Kahnooj earthquake (2011/06/15, MS=5.7) and the Sirch earthquake (2011/06/26, MS=5.2) have occurred in Kerman province (one of seismologically active area in eastern Iran). The earthquakes have been relocated and processed using local and regional recorded seismograms. Mechanism of the earthquakes were calculated using the first P motion method. Processing both locations and focal mechanisms indicate that these earthquakes are probably related to the Lalehzar, Sabzevaran and Golbaf fault systems, respectively. Bardsir and Sirch earthquake faults dip northeastward and Kahnooj earthquake fault dips eastward, indicating that both source faults dip steeply. Mechanisms of the earthquakes were right lateral strike slip, reverse with right lateral strike slip component and reverse mechanism, respectively. Finally, this research is in accordance to the field investigations, in which the maximum intensity in MM and JMA scales was estimated ~VI near epicentral area and no co-seismic surface rupture were detected for these earthquakes.}, keywords = {Focal mechanism,Bardsir,Sirch,Kahnooj,Earthquake fault}, title_fa = {بررسی لرزه‌ای زمین‌لرزه 2010 بردسیر و زمین‌لرزه‌های 2011 سیرچ و کهنوج در استان کرمان}, abstract_fa = {در طول یک سال سه زمین‌لرزه بردسیر (31/07/2010) با بزرگای MS=5.8، زمین‌لرزه کهنوج (15/06/2011) با بزرگای MS=5.7 و زمین‌لرزه سیرچ (26/06/2011) با بزرگای MS=5.2 در استان کرمان (یکی از مناطق لرزه‌ای جنبا در ایالت لرزه‌ زمین‌ساختی خاور ایران) روی دادند. این زمین‌لرزه‌ها بر پایه لرزه‌نگاشت‌های برداشت شده در شبکه لرزه‌نگاری محلی و شبکه‌های لرزه‌نگاری ناحیه‌ای دوباره کانون‌یابی شده و سازوکار آنها نیز با روش نخستین جنبش موج P به ‌دست آورده شد. کانون‌یابی و برآورد سازوکار کانونی آنها نشان می‌دهد، به‌گمان این زمین‌لرزه‌ها وابسته به گسل‌های لاله‌زار، سبزواران و گلباف می‌باشند. شیب تند گسل‌های زمین‌لرزه‌های بردسیر و سیرچ، رو به شمال خاوری و هم‌چنین شیب تند گسل زمین‌لرزه کهنوج رو به خاور می‌باشد. سازوکار به ‌دست آمده برای این سه زمین‌لرزه، به‌ ترتیب راستالغز راست‌بر، معکوس با مولفه راستالغز راست‌بر و معکوس می‌باشند. سرانجام، می‌توان گفت نتایج این پژوهش با بررسی‌های میدانی زمین‌لرزه بردسیر، که بر پایه آن بیشینه شدت در سنجه‌های MM و JMA در گستره نزدیک به رومرکز، VI بوده و هیچ شکستگی وابسته به این زمین‌لرزه در بازدید میدانی از پیرامون رو کانون آن یافت نشده است، هم‌خوانی دارد.}, keywords_fa = {سازوکار,بردسیر,سیرچ,کهنوج,گسل زمین‌لرزه‌ای}, url = {https://esrj.sbu.ac.ir/article_96871.html}, eprint = {https://esrj.sbu.ac.ir/article_96871_1d15dfbeb6a1464ff00555d132287a01.pdf} } @article { author = {Rezaei, Sara and M. Torab, Farhad}, title = {A comparison between biogeochemical and secondary lithogeochemical halos in order to explore copper deposits and analyzing different stage of preparation and analytical errors in Darreh-Zerreshk mining area}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {49-66}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.49}, abstract = {The objective of this research is an investigation on variations and relationship between different elements in soil and various plant species in Darreh-Zerreshk mining area and its comparison between elements distribution in barren zones. On the basis of this research can propose a suitable geochemical exploration for discovering hidden ore deposits in the district and peripheral zones. For this purpose, 32 samples from two different fractions of B-horizon of soil from mineralized and barren zones and 29 plant samples from different species were taken and after preparation were analyzed for copper, iron, lead and zinc by AAS analytical method. In the first stage by preparation and analysis of duplicate samples, the different stage errors were analyzed and concluded that the 3-acid dissolution procedure is the best preparation method and the precision of different steps are in acceptable range. In the next stage, the correlation between elements and their Biological Absorption Coefficients (BAC) were investigated. The recent study demonstrates that due to variety of species, dispersion and sparsity of the plants and the effect of different biological factors, the use of biogeochemical method as a tool in copper exploration in the area is challengeable. However, secondary lithogeochemical environment such as soil can be introduced as most suitable sampling environment because it can demonstrate the highest copper concentration in contrast between mineralized and barren zones.}, keywords = {Darreh Zerreshk,Biological absorption coefficient,Secondary lithogeochemical,Copper,Biogeochemical sampling}, title_fa = {مقایسه هاله‌های بیوژئوشیمیایی و لیتوژئوشیمیایی ثانویه به‌منظور اکتشاف ذخایر مس و تحلیل خطای مراحل مختلف آماده‌سازی و آنالیز نمونه‌ها در منطقه معدنی مس دره‌زرشک}, abstract_fa = {هدف از انجام این تحقیق بررسی تغییرات و ارتباط عناصر مختلف در خاک و گونه­های مختلف گیاهان موجود در منطقه معدنی دره زرشک و مقایسه توزیع آنها با مناطق فاقد کانی­سازی بوده است تا بر این اساس بتوان روش مناسبی از اکتشافات ژئوشیمیایی به منظور کشف ذخایر پنهانی مس در منطقه و مناطق اطراف پیشنهاد نمود. بر این اساس تعداد 32 نمونه از دو فراکسیون مختلف از افق B خاک از مناطق کانی­سازی و فاقد کانی­سازی و تعداد 29 نمونه از گونه­های مختلف گیاهی موجود در منطقه برداشت و پس از آماده سازی به روش جذب اتمی برای عناصر مس، آهن، سرب و روی آنالیز شدند. در مرحله اول با آماده سازی نمونه­ها به روش­های مختلف و آنالیز نمونه­های تکراری، خطای مراحل مختلف تحلیل شد و مشخص گردید روش آماده سازی به شیوه سه اسید مناسب ترین روش انحلال بوده و دقت آماده­سازی به این شیوه و آنالیز نمونه­ها در محدوده قابل قبول قرار دارد. در مرحله بعد ضرایب هم­بستگی و ضریب جذب زیست ‌شناختی عناصر محاسبه و تحلیل گردید. مطالعات اخیر نشان داد که به دلیل ماهیت گونه­ها، تنوع زیاد، پراکنده بودن و عدم تراکم کافی گیاهان در منطقه و تاثیر عوامل مختلف زیستی و بیولوژیکی، استفاده از روش بیوژئوشیمیایی به عنوان یک ابزار اکتشافی در اکتشاف مس در منطقه با چالش همراه است ولی محیط لیتوژئوشیمیایی ثانویه مثل خاک برجا می­تواند مناسب­ترین محیط نمونه­برداری قلمداد شود چرا که بیشترین تباین را در غلظت مس بین زون کانی­سازی و مناطق عقیم نشان می­دهد.}, keywords_fa = {دره زرشک,ضریب جذب زیست‌شناختی,لیتوژئوشیمیایی ثانویه,مس,نمونه‌برداری بیوژئوشیمیایی}, url = {https://esrj.sbu.ac.ir/article_96878.html}, eprint = {https://esrj.sbu.ac.ir/article_96878_f97624e154c2f102c46943b1ed5afcec.pdf} } @article { author = {Ebrahimi, Susan and Arabamiri, Alireza and Biari, Hadi}, title = {Evidences of the manto type copper mineralization in the Asmanou area (Shahrood North East), on the basis of mineralogy, alteration and fluid inclusion characteristics}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {67-85}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.67}, abstract = {The Asmanou deposit is located in 85 km east of Shahrood, in the Sabzevar zone and Toroud- Abbas Abad district. The host rocks of mineralization are pyroxene andesite, basalt, basaltic trachyandesite and trachybasalt which display shoshonitic affinity and characteristic of continental arc setting. The country rocks in the Asmanou variably altered and two type of alterations, regional and local, could be distinguished; zeolite- carbonate regional alteration is widespread in the area and local alteration associated to the mineralization are chloritic and hematitic. Mineralization occurs as vein and stratiform and the common textures are disseminated, vein- veinlet, stock work and open space filling. Chalcosite is the main ore mineral accompanied by subordinate magnetite, hematite, bornite, chalcopyrite, pyrite and secondary minerals including covelite, malachite, coprite and goethite. Nonmetallic minerals are calcite, quartz, chlorite and zeolite. Fluid inclusion studies from the calcite and quartz from the main hypogene stage yielded the homogenization temperature between 79 to 350 °C for calcite, and 160 to 250 °C for quartz. Salinities for calcite is between 2.3 to 22 wt% NaCl eq. and for quartz between 6.1 to11.3 wt% NaCl eq. The results of this studies show the mixing and boiling are two important factors in the mineralization. Geophysical studies using resistivity (Rs) and induction polarization (IP) show the high values of IP-Rs in 5 to 40 m depth. Mineralogy, ore texture and structure, and fluid inclusion characteristics in the Asmanou deposit are similar to those manto type copper deposits. }, keywords = {Asmanou,Geophysics (IP-Rs),Fluid inclusion,Shahrood,Copper Manto type}, title_fa = {شواهد کانی‌سازی مس نوع مانتو در منطقه آسمانو (شمال‌شرق شاهرود)، بر اساس ویژگی‌های کانی‌شناسی، دگرسانی و میانبارهای سیال}, abstract_fa = {محدوده معدنی آسمانو در 85 کیلومتری شمال­شرق شهرستان شاهرود واقع شده و از نظر زمین­شناسی در زون سبزوار و ناحیه معدنی ترود- عباس­آباد قرار می­گیرد. سنگ­های میزبان کانی­سازی شامل پیروکسن آندزیت، بازالت، تراکی­آندزیت بازالت و تراکی­بازالت ائوسن هستند که ماهیت آلکالن داشته و از دیدگاه زمین­ساختی در موقعیت کمان حاشیه فعال قاره­ای قرار می­گیرند. واحدهای آتشفشانی موجود در منطقه، سه نوع دگرسانی در مقیاس ناحیه­ای و محلی را متحمل شده­اند. دگرسانی زئولیتی- کربناتی، به­صورت ناحیه­ای بخش وسیعی از سنگ­های منطقه را تحت­تاثیر قرار داده ­است و دگرسانی­های کلریتی و هماتیتی محلی بوده و با مناطق کانه­زایی مرتبط می­باشند. کانه­زایی به­صورت رگه­ای و چینه­کران تشکیل شده و دارای بافت پراکنده، داربستی، رگه - رگچه­ای و پرکننده فضای خالی است. کالکوسیت کانی اصلی مس می­باشد؛ که با مقادیری مگنتیت، بورنیت، هماتیت، کالکوپیریت و پیریت و کانی­های ثانویه مانند مالاکیت، کوولیت، کوپریت، گوتیت و دیژنیت همراه می­باشند. زئولیت، کلسیت، کوارتز و کلریت کانی­های غیرفلزی هستند. مطالعات میانبارهای سیال بر روی کانی­های کلسیت و کوارتز مربوط به مرحله اصلی کانی­سازی، دمای همگن­شدگی را برای کلسیت 79 تا 350 و  برای کوارتز 160 تا 250 درجه ­سانتیگراد نشان می­دهد. دامنه تغییرات شوری برای کانی کلسیت 3/2 تا 22 و برای کوارتز 1/6 تا 3/11 درصد وزنی نمک طعام می­باشد. نتایح حاصل از مطالعات میانبارهای سیال نشان می­دهد، فرایند جوشش و اختلاط دو عامل مهم در تشکیل کانه­زایی می­باشند. مطالعات ژئوفیزیک با استفاده از دو متد مقاومت ویژه (Rs) و پلاریزاسیون القایی (IP) مقادیر بالایی از (IP-Rs) را در عمق 5  تا 40 متری نشان داده­ است. با توجه به ویژگی­های زمین­شناسی، کانی­شناسی، بافت و ساخت کانسنگ و داده­های حاصل از میانبارهای سیال، کانی­سازی آسمانو قابل مقایسه با ذخایر مس نوع مانتو می­باشد. }, keywords_fa = {آسمانو,ژئوفیزیک (IP-Rs),سیالات درگیر,شاهرود,مس نوع مانتو}, url = {https://esrj.sbu.ac.ir/article_96884.html}, eprint = {https://esrj.sbu.ac.ir/article_96884_d71a41451221d2042de8deead5fda237.pdf} } @article { author = {Yousefi Hajivand, Asiyeh and Adabi, Mohammad Hoseyn and Sadeghi, Abbas}, title = {Microfacies, sedimentary environment and diagenesis of the Asmari Formation in Chahar Bisheh Oil Field, south west of Iran}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {86-113}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.86}, abstract = {In this research, two subsurface  sections consist of well No.2 and No.3 from the Asmari Formation with a thickness of 423 and 412 m respectively in Chahar Bisheh oil Field have been studied. The Asmari Formation in this field consists of intermittent layers of limestone and dolomite, very thin shale layers and anhydrite interlayers. Based on petrographic studies and identification of microfacies, 15 microfacies and 1 lithofacies in 4 facies belts consist of tidal flats, lagoon, shoal and open marine for the Asmari Formation have been recognized and sedimentary environment of this formation, is a Homocline ramp carbonate platform. Effective diagenetic processes including cementation, dolomitization, compaction, fracturing, dissolution, micritization, pyritization, geopetal fabric, boring, silicification and neomorphism which has influenced the Asmari Formation by all three marine, meteoric and burial diagenetic environments.}, keywords = {Diagenesis,Asmari Formation,Sedimentary environment,Microfacies}, title_fa = {ریز رخساره، محیط رسوبی و دیاژنز سازند آسماری در میدان نفتی چهاربیشه جنوب غرب ایران}, abstract_fa = {در این پژوهش سازند آسماری در دو مقطع تحت­الارضی به نام­های چاه­ شماره 2 و شماره 3 میدان نفتی چهاربیشه به ترتیب با ضخامت­های 423 و 412 متر مورد بررسی قرار گرفته است. سازند آسماری در این میدان از تناوبی از لایه­های سنگ آهک و دولومیت همراه با لایه­های بسیار نازک شیل و میان لایه­های انیدریت تشکیل شده است. بر اساس مطالعات پتروگرافی و شناسایی ریز رخساره­ها، تعداد 15 ریز رخساره و 1 لیتوفاسیس در قالب 4 کمربند رخساره­ای پهنه جزرومدی، لاگون، سد و دریای باز برای سازند آسماری معرفی و محیط رسوبی این سازند، پلاتفرم کربناته از نوع رمپ هم شیب (هموکلاین) تعیین گردیده است. از فرایندهای دیاژنزی تاثیرگذار می­توان سیمانی­شدن، تراکم (فیزیکی و شیمیایی)، انحلال، تخلخل­های اولیه و ثانویه، فابریک ژئوپتال، نئومورفیسم افزایشی، جانشینی (دولومیتی­شدن، آهن­دار شدن و سیلیسی شدن)، میکریتی­شدن و بورینگ را بیان کرد که در قالب هر سه محیط دیاژنزی متائوریکی، دریایی و تدفینی، سازند آسماری را تحت تاثیر قرار داده­اند.}, keywords_fa = {دیاژنز,سازند آسماری,محیط رسوبی,ریز رخساره}, url = {https://esrj.sbu.ac.ir/article_96896.html}, eprint = {https://esrj.sbu.ac.ir/article_96896_2d59011eb6c66d7abdaf848d1f310b85.pdf} } @article { author = {Mohammadi Karagouz, masum and momivand, hasan}, title = {Effects of orientation, frequency and number of sets of discontinuities on the rock permeability before and after improvement by cement grouting}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {114-127}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.114}, abstract = {Discontinuities are the most important property of rock mass that control the permeability. Effects of orientation, frequency and number of sets of discontinuities on the permeability investigated before and after improvement by grouting using cement grout in this study. Rock samples having one, two and three cross-sets of single discontinuities and three cross-sets of discontinuities with one set having four parallel discontinuities, in different groups of various orientations (angle between planes of discontinuities and horizontal direction) of 0, 30, 45, 60 and 90 degrees in total of 20 different groups that have been preparing. The permeability of 20 group samples with different orientation, frequency and number of set of discontinuities has been measured. Discontinuities of multiple groups of samples using cement grout improved and also their permeability measured. The results show that the effect of discontinuities’s orientation on permeability changes by changing the number sets and the frequency of discontinuities. In samples having three cross-sets of perpendicular discontinuities with one set having four parallel discontinuities which have been represented jointed rock mass. Permeability is mainly affected by the orientation of the set that has four parallel discontinuities. Orientation, frequency and number of sets of discontinuities cause change in permeability about 759048 times. The permeability reduces in the range of 9-99% with the improvement of samples using cement grout injection. This indicates that the orientation, frequency and number of sets of discontinuities are very effective in reducing permeability by the injection.}, keywords = {Orientation,Number of sets,Frequency,Discontinuities,Permeability,Injection,Rock}, title_fa = {تأثیر جهت یافتگی، تعداد دسته و فراوانی ناپیوستگی‌های سنگ قبل و بعد از بهسازی با تزریق سیمان در میزان نفوذپذیری}, abstract_fa = {ناپیوستگی­ها مهم­ترین ویژگی توده سنگ برای کنترل نفوذ­پذیری هستند. در این تحقیق تأثیر ناپیوستگی­های دارای جهت­یافتگی، فراوانی و تعداد دسته­های متقاطع در نفوذپذیری سنگ قبل و بعد از بهسازی با تزریق دوغاب سیمان مورد بررسی قرار گرفته است. نمونه­های سنگ فاقد ناپیوستگی، دارای یک دسته ناپیوستگی، دو دسته ناپیوستگی، سه دسته ناپیوستگی متقاطع منفرد و سه دسته ناپیوستگی متقاطع که یک دسته آن­ها دارای چهار ناپیوستگی موازی بوده در گروه­های مختلف دارای زاویه شیب صفحه ناپیوستگی­ها با جهت افقی به ترتیب 0، 30، 45، 60 و 90 درجه در مجموع شامل 20 گروه مختلف آماده­سازی شده­اند. میزان نفوذپذیری 20 گروه نمونه­های دارای ناپیوستگی با جهت­یافتگی، تعداد دسته­های متقاطع و فراوانی مختلف اندازه­گیری شده است. ناپیوستگی­های گروه­های متعدد نمونه­ها با استفاده از دوغاب سیمان بهسازی شده و میزان نفوذپذیری آن­ها نیز اندازه­گیری شده است. نتایج به دست آمده نشان می­دهد که روند تأثیر جهت یافتگی ناپیوستگی­ها بر نفوذپذیری با تغییر تعداد دسته ناپیوستگی­ها و فراوانی آن­ها تغییر می­نماید. در نمونه­های دارای سه دسته ناپیوستگی متقاطع و عمود برهم و یکی از دسته­ها دارای چهار ناپیوستگی موازی که مصداق سنگ به شدت درزه­دار بوده، نفوذپذیری بیشتر متأثر از جهت یافتگی دسته دارای چهار ناپیوستگی موازی است. تأثیر جهت یافتگی، تعداد دسته­درزه­ها و فراوانی آن­ها باعث شده که نفوذپذیری 759048 برابر تغییر نماید. با بهسازی نمونه­ها با استفاده از تزریق دوغاب سیمان مقدار نفوذپذیری با کمترین تأثیر با ضریب 9% تا بیشترین تأثیر با ضریب 99% کاهش یافت. این نشان می­دهد که جهت یافتگی، تعداد دسته­درزه­ها و فراونی آن­ها در کاهش نفوذپذیری بر اثر تزریق خیلی مؤثر است.}, keywords_fa = {جهت یافتگی,تعداد دسته,فراوانی,ناپیوستگی‌ها,نفوذ‌پذیری,تزریق,سنگ}, url = {https://esrj.sbu.ac.ir/article_96815.html}, eprint = {https://esrj.sbu.ac.ir/article_96815_4a200d96c1709f4e254270be8af9203c.pdf} } @article { author = {Hosseini, Seyed musa and Ghadiri, Hajar and Garavand, Fatemeh}, title = {Investigation of hydrological characteristics of Damghan Cheshmeh-Ali karst aquifer}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {128-145}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.128}, abstract = {Damghan Cheshmeh-Ali spring with average daily discharge of 140 lit/s plays main role in supplying the domestic and agriculture water demands in this area. In this study, daily precipitation and discharge data series from 2001-2010 were used for investigating of hydrological characteristics of the karst aquifer connected to this spring. Mangin’s classification method indicates that the unsaturated zone of the Cheshmeh-Ali karst aquifer has more karstification degree compared to the saturated zone. Cross correlation analysis between cumulative rainfall (daily to 360 days) and daily spring discharge data indicated that the rainfall series of current day to 300 days have more correlation with the spring flow in current day. In addition, frequency analysis of drought hydrological carried out on the spring low flow and with duration of 3, 7, and 10 days indicated that discharge with probability of 99% is obtained as 350, 262, and 213 lit/s respectively for duration of 3, 7, and 10 days. Whereas, significant difference is observed between the predicted discharge with periods of 3, 7, and 10 days for less than 5 years return duration.}, keywords = {Drought analysis,Effective rainfall,Cheshmeh-Ali,Mangin’s method,Karst aquifer}, title_fa = {بررسی ویژگی‌های هیدرولوژیکی آبخوان کارستی چشمه‌علی دامغان}, abstract_fa = {چشمه­علی دامغان با متوسط آبدهی روزانه 140 لیتر در ثانیه اهمیت زیادی در تأمین نیازهای شرب و کشاورزی منطقه دارد. در این تحقیق با بررسی آماری داده­های بارش و دبی روزانه چشمه از سال 1380 الی 1388، درک عمیق­تری از ویژگی­های هیدرولوژیکی این آبخوان کارستی ارائه شده است. براساس طبقه­بندی آبخوان کارستی مانجین، سیستم مجرایی در بخش بالایی آبخوان، نسبت به بخش­های نزدیک به خروجی چشمه از درجه توسعه یافتگی بالاتری برخوردارند. آنالیز هم­بستگی متقاطع بین داده­های دبی روزانه چشمه و بارندگی تجمعی (1 تا 365 روزه) نشان داد بارش­های همان روز تا 300 روز قبل بر جریان خروجی چشمه در روز متناظر تأثیر قابل توجهی دارند. آنالیز خشکسالی هیدرولوژیک دبی چشمه به روش جریان­های کمینه و با تداوم­های 3، 7 و 10 روزه نشان داد که آبدهی متوسط روزانه چشمه که در 99% مواقع می­توان انتظار داشت به ترتیب برابر و کمتر از 350، 262 و 213 لیتر بر ثانیه باشد. هم­چنین برای دوره­های بازگشت کمتر از 5 سال که دارای احتمال وقوع بالایی نیز هستند تفاوت چندانی بین دبی­های پیش­بینی شده مشاهده نمی­شود.}, keywords_fa = {آنالیز خشکسالی,بارش مؤثر,چشمه علی,روش مانجین,آبخوان کارستی}, url = {https://esrj.sbu.ac.ir/article_96826.html}, eprint = {https://esrj.sbu.ac.ir/article_96826_f11dadf3ca4b643a9f14094df7180801.pdf} } @article { author = {Motamedi Rad, Mohammad and Goli Mokhtari, Leila and Bahrami, Shahram and zanganeh asadi, Mohammad ali}, title = {Assessment of the heavy- metal pollution in sediments of the Roein karstic basin}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {146-166}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.146}, abstract = {One of the most important environmental issues which can affect the health of plants, animals and humans is soil pollution by the concentration of the heavy metals. The increase of heavy metal concentration can occur due to the natural processes or human activities. The present study deals with examining and assessing the concentration and contamination of the heavy elements in the sediments.  Roein    basin in Esfarayen area was selected for this purpose and the concentration of 11 heavy metals, including As (Arsenic), Cd (Cadmium), Co (Cobalt), Cr (Chrome), Cu (Copper), Fe (Iron), Mo (Molibden), Ni ( Nickel), Pb (Lead), V (Vanadium) and Al (Aluminum) were measured in 42 samples and the correlation of the elements was examined. The results showed that there is a significant correlation between the copper and iron content (0.99), iron and aluminum (0.93), cobalt and copper (91), cobalt and iron (0.89), chrome and nickel (0.88), copper and aluminum (0.85), cobalt and aluminum (0.82), arsenic and aluminum (0.72), nickel and lead (0.7). Then, the contamination factors such as enrichment factor, contamination factor, modified contamination degree, pollution load index and geo-accumulation index were computed and assessed. All the indexes were calculated except the enrichment factor which depend on the elements existing on the crust of the earth and the arsenic is categorized as strong, suggesting that although the eleven elements studied contain various contents, they all are categorized as the non-polluting and therefore, there is no significant contamination in terms of heavy elements concentration in the area. Since, there is currently a higher increase in the heavy metal concentration, higher control shall be applied regarding the agricultural and industrial activities.}, keywords = {Pollution,Heavy Metals,Roein basin,Enrichment,Kriging}, title_fa = {ارزیابی میزان آلودگی ناشی از عناصر سنگین در رسوبات حوضه کارستی روئین}, abstract_fa = {یکی از مهمترین مسائل زیست محیطی که می‌تواند بر سلامت گیاهان، جانوران و انسانها تاثیر بسزایی داشته، میزان غلظت عناصر سنگین در خاک و آلودگی آن می‌باشد. افزایش غلظت فلزات سنگین می­تواند با توجه به فرآیندهای طبیعی یا فعالیت­های انسانی رخ دهد. پژوهش حاضر به بررسی و ارزیابی میزان غلظت و آلودگی عناصر سنگین در رسوبات می‌پردازد. بدین منظور حوضه روئین در شهرستان اسفراین انتخاب و غلظت 11 عنصر سنگین شامل As (آرسنیک)،Cd  (کادمیوم)،Co  (کبالت)، Cr (کروم)، Cu (مس)، Fe (آهن)، Mo (مولیبدن)،  Ni(نیکل)، Pb(سرب)، V (وانادیم) و Al (آلومینیوم) در42 نمونه و میزان همبستگی عناصر مورد بررسی قرار گرفت. محاسبات نتایج نشان داد وجود ضریب همبستگی معناداری بین مقادیر مس و آهن (993/0)، آهن و آلومینیوم (930/0)، کبالت و مس (908/0)، کبالت و آهن (897/0)، کروم و نیکل (879/0)، مس و آلومینیوم (853/0)، کبالت و آلومینیوم (818/0)، آرسنیک و آلومینیوم (719/0) و نیکل و سرب (702/0) می‌باشد. سپس شاخص‌های آلودگی نظیر فاکتور غنی شدگی، ضریب آلودگی، درجه آلودگی اصلاح شده، ضریب بار آلودگی و شاخص زمین انباشتگی مورد محاسبه و ارزیابی قرار گرفت. تمامی شاخص‌های مورد محاسبه به جز شاخص فاکتور غنی شدگی که بر اساس میانگین عناصر پوسته زمین می‌باشد و عنصر آرسنیک آن در طبقه شدید قرار گرفت، بیانگر این نکته می‌باشند که یازده عنصر مطالعاتی گر چه دارای مقادیر متفاوتی هستند ولی همگی در طبقه بدون آلودگی قرار گرفته­اند و لذا منطقه مورد مطالعه از نظر غلظت عناصر سنگین دارای آلودگی قابل توجهی نمی‌باشد. اما از آنجا که در حال حاضر بیشتر افزایش غلظت عناصر سنگین دارای منشا انسانی می‌باشد باید کنترل بیشتری در رابطه با فعالیت­های کشاورزی و صنعتی صورت گیرد.}, keywords_fa = {آلودگی,عناصر سنگین,حوضه روئین,غنی شدگی,کریجینگ}, url = {https://esrj.sbu.ac.ir/article_96831.html}, eprint = {https://esrj.sbu.ac.ir/article_96831_20e7ed3df8e7a3643803c6a52e114a5a.pdf} } @article { author = {parvin, mansour and negahban, saeed}, title = {The effect of geomorphologic and geological characteristic on the recharge of alluvial aquifers (case study: Gilan-e- Gharb alluvial aquifer)}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {167-180}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.167}, abstract = {The formation and subsequent recharge of alluvial aquifers depend on the geological conditions, geomorphology, climate, and land cover.This type of aquifer plays main role in supplying the water needed by human societies in arid and semi-arid regions of the country and mainly due to excessive perceptions, they require the development and implementation of management plans. Alluvial aquifers in the  Gilan-e- gharb have been equilibrium due to favorable environmental conditions until the mid-1970s.But gradually, due to human interference in the hydrology cycle of the region and the occurrence of dry periods, the Gilan-e-gharb aquifer falls to the surface and requires the formulation and implementation of management plans.In this research, modeling of alluvial aquifer susceptible habitats was performed based on six lithology parameters, linear density, drainage density, geomorphology, land use and slope. About 23.8% of the area has a high groundwater abundance potential and 44% of the area has a low potential for groundwater and these areas are prone to runoff. Therefore, the special geomorphological and lithological conditions of the area have caused the natural recharge of aquifers to be limited and requires the implementation of artificial recharge plans.}, keywords = {Alluvial aquifer,Artificial recharge,Geomorphology,Geology,Gilan-e-Gharb}, title_fa = {ارزیابی تاثیرات ویژگی‌های ژئومورفولوژیک و زمین‌شناسی بر چگونگی تغذیه آبخوان‌های آبرفتی (مطالعه‌ای موردی: آبخوان آبرفتی گیلانغرب)}, abstract_fa = {شکل­گیری و به دنبال آن تغذیه آبخوان­های آبرفتی وابسته به شرایط زمین­شناسی، ژئومورفولوژیکی، اقلیمی و پوشش زمین است. این نوع آبخوان­ها نقش بسیار مهمی در تامین آب مورد نیاز جوامع بشری در مناطق خشک و نیمه خشک کشور داشته و عمدتا به علت برداشت بیش از حد نیازمند تدوین و اجرای برنامه­های مدیریتی هستند. آبخوان آبرفتی گیلانغرب امروزه به دلیل برداشت بی­رویه، رخداد خشکسالی­های دو دهه­ای اخیر و محدودیت طبیعی در تغذیه به خصوص در نواحی کوهستانی شمال آن از حالت تعادل خارج شده است. در حال حاضر با توجه به ادامه­ای شرایط ذکر شده، آبخوان گیلانغرب کماکان در معرض پیامدهای زیانبار این عوامل بوده و نیازمند تدوین و اجرای برنامه­های مدیریتی است. هدف این پژوهش مدل­سازی حوضه­ای تغذیه­ای آبخوان، به منظور ارائه راهکاری­های مدیریتی برای آبخوان گیلانغرب است. در این پژوهش مدل­سازی مناطق مستعد تغذیه آبخوان آبرفتی بر اساس شش پارامتر لیتولوژی، تراکم خطواره، تراکم زهکشی، ژئومورفولوژی، کاربری اراضی و شیب توپوگرافی انجام گرفت. حدود 88/23 % مساحت منطقه دارای پتانسیل زیاد تغذیه آب زیرزمینی است و 44% مساحت منطقه دارای پتانسیل کم برای تغذیه آب زیرزمینی بوده و این مناطق مستعد ایجاد رواناب هستند. بنابراین شرایط خاص ژئومورفولوژیکی و لیتولوژیکی منطقه سبب شده که تغذیه طبیعی آبخوان دارای محدودیت بوده و نیازمند اجرای طرح­های تغذیه مصنوعی می­باشد.}, keywords_fa = {آبخوان آبرفتی,تغذیه مصنوعی,ژئومورفولوژی,زمین‌شناسی,گیلانغرب}, url = {https://esrj.sbu.ac.ir/article_96841.html}, eprint = {https://esrj.sbu.ac.ir/article_96841_fb09ef6a683f589ec674c04c940c8c68.pdf} } @article { author = {shakiba, ََAlireza and matkan, Ali akbar and mirbagheri, Babak and seif, Yaghub}, title = {Vulnerability assess of the levels and prioritization of rural settlements against earthquakes using Fuzzy Logic in GIS (case study: Fars Province)}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {181-200}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.181}, abstract = {One of the natural disasters that plays a major role in the vulnerability and destruction of rural settlements is earthquake. Vulnerability has a complex concept so that involves various factors and variables and using modern methods could improve vulnerability assess of the levels. The objective of this study is to vulnerability assess the levels and prioritization of rural settlements with the use of operators based on Fuzzy Logic. The Fars province was selected as a case study because of exist many major and minor faults, during the years occured huge earthquakes and theirs rural settlements have a variety of natural and human vulnerability. Because of the physical characteristics, rural areas exposured to high vulnerability is compared with urban areas. In this study, for vulnerability assess the levels and prioritization was used fuzzy operators that including multi criteria aggregation criterion importance and orders weight and two important properties consider to qualitative (linguistic) variables and according to various interest groups and also led to better results. Therefore, by using and aggregating various variables and scenarios, areas with high degrees of risk identified. Then rural settlements exposure risk resulting from relatively pessimistic scenario of natural vulnerability was choiced. Eventually, the human vulnerability of settlements have been prioritized using a moderate scenario. The results in all scenarios showed that South and West areas with high values of Peak Horizontal Acceleration, new geological formations and proximity to active faults as areas with high degrees natural vulnerability of risk has been identified and always happening huge earthquakes but from the perspective of human vulnerability variables is moderate.}, keywords = {Fars Province,Firozabad,vulnerability,Rural settlements,Earthquake,Fuzzy logic}, title_fa = {سنجش سطوح و اولویت‌بندی آسیب‌پذیری سکونتگاه‌های روستایی در برابر زلزله با استفاده از منطق فازی در GIS (مطالعه موردی: استان فارس)}, abstract_fa = {از مهم­­ترین بلایای طبیعی که نقش مهمی در آسیب­پذیری و تخریب سکونتگاه­های روستایی ایفا می­نماید، زلزله می­باشد. آسیب­پذیری دارای مفهومی پیچیده است به طوری که عوامل و متغیرهای مختلفی در آن دخالت دارد و استفاده از روش­های نوین موجب بهبود فرآیند سنجش سطوح آسیب­پذیری می­شود. هدف از ارائه پژوهش حاضر، سنجش سطوح و اولویت­بندی آسیب­پذیری سکونتگاه­های روستایی با به کارگیری عملگرهای مبتنی بر منطق فازی می­باشد. استان فارس که دارای گسل­های اصلی و فرعی متعددی بوده و در طول سالیان گذشته زلزله­های متعددی با قدرت تخریب بالا در آن به ­وقوع پیوسته و هم­چنین، سکونتگاه­های روستایی آن دارای تنوع آسیب­پذیری طبیعی و انسانی می­باشد، به عنوان منطقه­ی مطالعاتی انتخاب شده است. سکونتگاه­های روستایی از محیط­هایی به شمار می­رود که به دلیل ویژگی­های فیزیکی آن در مقایسه با سکونتگاه­های شهری در معرض آسیب­پذیری بیشتری می­باشد. در این پژوهش، جهت سنجش سطوح و اولویت­بندی آسیب­پذیری از عملگرهای فازی که شامل تلفیق چندمعیاره اهمیت معیارها و وزن­ رتبه­ها بوده و دو ویژگی مهم در نظرگرفتن متغیرهای کیفی (زبانی) و توجه به گروه­های مختلف ذینفع را نیز داشته و هم­چنین، به نتایج بهتری منجر شده، استفاده گردید. لذا با به کارگیری و تلفیق متغیرها و سناریوهای مختلف، مناطق با درجات بالای ریسک مشخص شد. سپس، سکونتگاه­های روستایی در معرض ریسک حاصل از سناریوی نسبتا بدبینانه آسیب­پذیری طبیعی انتخاب گردید. در نهایت، آسیب­پذیری انسانی این سکونتگاه­ها با به کارگیری سناریوی متعادل اولویت­بندی شد. نتایج حاصل در تمامی سناریوها نشان داد که بخش­های جنوب و غرب منطقه که دارای مقادیر بالای بیشینه جنبش افقی زمین (Peak Horizontal Acceleration)، سازندهای زمین­شناسی جدید و نزدیکی به گسل­های فعال زمین­شناسی بوده به عنوان مناطق با درجات بالای ریسک آسیب­پذیری طبیعی شناسایی شده و همواره زلزله­های متعدد با قدرت تخریب بالا در آن به وقوع می­پیوندد اما از منظر متغیرهای آسیب­پذیری انسانی مورد استفاده در این پژوهش در حد متوسط می­باشند.}, keywords_fa = {استان فارس,آسیب پذیری,سکونتگاه های روستایی,زلزله,منطق فازی}, url = {https://esrj.sbu.ac.ir/article_96848.html}, eprint = {https://esrj.sbu.ac.ir/article_96848_8afb8730662ad0648926ba77332eaece.pdf} } @article { author = {َAbbasi, Elham and Tvakoli, Jamileh and Sajadi, zhila and Sarrafi, Mozaffar}, title = {Qualitative meta-analysis of scholarly papers on the city-region}, journal = {Researches in Earth Sciences}, volume = {9}, number = {4}, pages = {201-220}, year = {2019}, publisher = {Shahid Beheshti University}, issn = {2008-8299}, eissn = {2588-5898}, doi = {10.29252/esrj.9.4.201}, abstract = {The city-region concept which is against theories such as “The death of distance”, “The end of geography” or the emergence of “weak economy” has recently become popular among academic and political elite. The city-region as the place of exchange, innovation, development and competition is an ideal area that identifies which economic competition can be promoted and cultivated. Hence, the identification of the context, the nature and reasons for the importance of the city-region pattern needs to be explained in an accurate manner. Various studies have been taken place on the city-region so far.In this paper using qualitative meta-analysis method, 45 scientific articles, published since 2000 are studied in a descriptive way and evaluated (in terms of questions, goals, and results). It seems that the necessity and application of this meta-analysis can be helpful in understanding the spatial nature of the city-region and identifying the role and position of it as a driving engine of the regions to balance and develop. The paper combines these  scientific works and provides a structural-functional analyses of the city-region pattern for academic and executive policy-makers institutions.}, keywords = {City-region,Qualitative meta-analysis,Competitive Advantage,New regionalism}, title_fa = {فراتحلیل کیفی از مقالات علمی ناظر بر شهر-منطقه}, abstract_fa = {مفهوم شهر- منطقه به تازگی تبدیل به یک الگوی محبوب در حوزه دانشگاه و سیاست شده، که در تباین با نظریه­هایی چون "مرگ فاصله"،"پایان جغرافیا" و یا ظهور "اقتصاد بی وزن" مطرح شده است. شهر- منطقه به عنوان مکان تجمیع، تشدید، توسعه و رقابت پدیده مطلوبی است که مشخص می­سازد کدام رقابت اقتصادی را می­توان ارتقاء و پرورش داد. از این رو شناسایی زمینه، ماهیت و دلایل اهمیت الگوی شهر-منطقه نیازمند تبیین و تدقیق مضاعف است. تاکنون پژوهش­های گوناگونی درباره شهر-منطقه­ها انجام شده است. این مقاله با استفاده از روش فراتحلیل کیفی، 45 مورد از مقالات علمی تولید شده از سال 2000 (از طریق جستجو در پایگاه داده­های علمی خارجی) را بررسی توصیفی نموده و در سه بعد سوال، هدف و نتیجه ارزیابی به عمل آمده است. ضرورت و کاربرد این فراتحلیل می­تواند در درک ماهیت فضایی شهر-منطقه و تبیین نقش و جایگاه آن به عنوان موتور محرکه مناطق در راستای تعادل و توسعه موثر باشد. در انتها با جمع­بندی آخرین تلاش­­­های علمی این نتیجه حاصل شد که شهر-منطقه ها، با نگرش پیوند اقتصادی دو مقیاس محلی و جهانی به دنبال ارتقاء توان رقابت پذیری و پایداری است و این امر از طریق نومنطقه گرایی امکان­پذیر می­شود. هم­چنین ارائه تحلیل­های ساختاری- عملکردی از الگوی شهر-منطقه برای نهادهای سیاست­گذار علمی و اجرایی ارائه گردید.}, keywords_fa = {شهر,منطقه,فراتحلیل کیفی,مزیت رقابتی,نومنطقه گرایی}, url = {https://esrj.sbu.ac.ir/article_96867.html}, eprint = {https://esrj.sbu.ac.ir/article_96867_1e12587991e5b03ce624a4d796a2f748.pdf} }